Plumber's Essentials: Your Key to Bathtub Installation
Plumber's Essentials: Your Key to Bathtub Installation
Blog Article
Everyone maintains their own individual idea when it comes to A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't specifically rocket science, yet it does need solid plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a new one is also a reasonably challenging job. If the old bathtub is readily obtainable, the project can move speedily; if you have to open a wall surface to eliminate the old bathtub and place the new bath tub, the task is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub and also embeded in the brand-new one. See to it you have certified on your own for the job as well as are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed project, it is much better to consider employing one before you start. Chances are you may require a specialist plumber to make tube connections.
This post will aid you install a new tub in your washroom if you have already gotten a new tub as well as don't need to alter the plan of your previous water supply pipes.
Your tools and material checklist must consist of the following:
Planning for the Setup
To start with, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing faucets can be fairly troublesome as a result of the limited access that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will come from the pipelines. Once the supply pipelines have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this process. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of both wooden boards under its feet, place the tub in the needed placement. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the bathtub till the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile faucet port to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the supply of water and examine all joints and brand-new pipework for leakages and tighten them if essential. Fill the tub as well as additionally examine the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's instruction manual. Tiling as well as securing around the tub needs to wait up until the bath tub has been utilized at the very least when as this will certainly settle it right into its final position.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area between the tap as well as the sink. Safeguard the faucet in position with the producer offered backnut. Once the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous kind must be linked to the tap finishes first, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture an inflexible seal, causing the water to penetrate the wall in between the bath as well as the tiling, leading to difficulties with moisture and also possible leakages to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can crack fairly early if you do not think about this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently available on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader on A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that piece of content was a smart idea. Liked our blog posting? Please share it. Let somebody else discover it. I enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Ensure plumbing integrity; reach out. Report this page